鋼跳板成型設備簡介 技術標準 1.1 GB/T6725-2002 《冷彎型鋼技術條件》 1.2 GB/T6728-2002 《結構用冷彎空心型鋼尺寸、外型、重量及允許偏差》 1.3 GB6723-86 《通用冷彎開口型鋼尺寸、外形、重量及允許偏差》 1.4 GB/709-88 《熱軋鋼板和鋼帶的尺寸、外形、重量及允許偏差》 1.5 GB/708-88 《冷軋鋼板和鋼帶的尺寸、外形、重量及允許偏差》 2.設備技術要求 2.1設備技術條件： 2.1.1設備占地面積：45×3.0×5（長×寬×高）米。（根據最后提供地基圖為準） 2.1.2設備進料方向：左進料。 2.1.3電壓參數380，50Hz，3相。 2.1.4氣源：流量為0.5m3/分鐘；壓力為0.6MPa。 2.1.5液壓油：46#液壓油。 2.1.6齒輪油：18#雙曲線齒輪油。 2.2設備主要技術參數 2.2.1 軋制帶鋼寬度：≤500 mm 2.2.2 軋制帶鋼厚度：2 mm 2.2.3 軋制帶鋼材質：GI 帶鋼 2.2.4生產速度:全線沖孔速度約為8米/分鐘以上 2.2.4 軋制工件長度：2000.6000 mm 2.2.5設備裝機總?cè)萘浚?4.9 KW。 3.軋制產品范圍 3.1 本沖壓/成型機組可以軋制厚度為2mm 的腳踏板型材。 3.2 軋制產品規格尺寸 （最終以客戶提供型材圖為準） 4.供貨及服務范圍 4.1本條款規定了合同設備的供貨范圍（見表二），賣方保證所提供設備為全新的、成熟的、完整的和安全可靠的，且設備的技術性能、功能符合技術條件的要求。 鋼跳板成型設備 Foot pedal device profile The technical standards 1.1 GB/T6725-2002 "the cold bending steel technical conditions" 1.2 GB/T6728-2002 "structure with cold bending hollow section size, shape, weight.allowable deviation" 1.3 GB6723-86 "general opening cold bend steel size, shape, weight.allowable deviation" 1.4 GB / 709-709 "hot rolled steel plate.steel belt of the size, shape, weight.allowable deviation" 1.5 GB / 708-708 "cold rolled steel plate.steel belt of size, shape, weight.allowable deviation" 2. The equipment technical requirements 2.1 equipment technical conditions: 2.1.1 equipment area: 45 * 3.0 * 5 meters (length x width x height). (according to finally provide foundation drawing shall prevail) 2.1.2 device feed direction: left feed. 2.1.3 voltage parameters for 380, 50 Hz, 3 phase. 2.1.4 gas source: flow of 0.5 m3 / min; Pressure is 0.6 MPa. 2.1.5 hydraulic oil: 46 # hydraulic oil. 2.1.6 gear oil: 18 # hyperbolic gear oil. 2.2 equipment main technical parameters 2.2.1 rolling strip width: 500 mm.less 2.2.2 rolling strip steel thickness: 2 mm 2.2.3 rolling steel strip material: GI strip steel 2.2.4 production speed: all punching speed is about more than 8 m/min 2.2.4 rolling workpiece length: 2000-6000 mm 2.2.5 equipment installed gross capacity: 44.9 KW. 3. Rolling product range 3.1 the stamping/molding unit can pedal profile rolling thickness of 2 mm. 3.2 size rolled products (final customer provide profile figure shall prevail) 4. The scope of supply.services The provisions of this clause 4.1 of the contract equipment scope of supply (see chart 2), the seller guarantees that the equipment for new, mature, complete,.safe.reliable,.the equipment of the technical performance.function accord with the requirement of technical conditions.